Home Intuition 2-Pack Leader and Gutter Guard from Leaves, Twigs, Branches Plastic Mesh Guards Leaf Protector 6" inch Wide 40' Feet Long Total

Really good product. I had to cut the tips of the little hooks to fit my gutter, but installation was easy and it's keeping the leaves out of my gutters. I would recommend.

Clips that secure the mesh material did not fit in my gutter. Fortunately, the product sets securely into the gutter well without the clips.

It took me a few tries to install. I did not use the plastic holders as I found them troublesome and instead chose to slip under shingles and secure the ends with a self tapping stew. It really wasn't that bad at all.

Difficult to install and will need to be removed for smaller debris when needing to clean the gutters.

I have traditional profiled aluminum gutters hung using standard hidden brackets purchased from a big box store. The mesh clips do not stay in place. Ended up having to secure each clip to the front of the gutters with a screw. My roof drip edge covers the back of the gutters so the only way to install these clips was to slide one edge of the clip/support piece up under the shingles. The mesh is cheap and broke multiple times while trying to snap it on the support clips. The mesh was too wide for my standard gutters so I had to either try and slide part of it up under the shingles, let it hang off the front edge of the gutter which looks terrible, let it lay on top of the shingles or cut it to width. Very very frustrating.FYI - I could not get it to lay flat on top of the shingles.Without a doubt the worst leaf guard system I have ever attempted to use. I would suggest you avoid it.

My property is surrounded by pines. The gutters currently installed are complete trash and I'm avoiding major upgrades at the moment. After weeks/hours of research my long-term options are expensive ones, new gutters with premium metal guards.No easy solutions exist for pine needles. Either the product you are installing has too small of holes (water will flow over your gutters) or too large (pine needles with get stuck in the guard) … and the most important problem: maintenance. No product exists that overcome these challenges + keep the cost low. So I’m creating that solution.My Build:Magnetic strip https://www.amazon.com/gp/product/B0799QD1MK/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1Half inch self tapping screws: https://www.amazon.com/gp/product/B008SPIQ2I/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1Zip tiesand the mesh product reviewed today https://www.amazon.com/Home-Intuition-Gutter-Plastic-Guards/dp/B07BDPP1KB/ref=asc_df_B07BDPP1KB/?tag=hyprod-20&linkCode=df0&hvadid=241973991106&hvpos=&hvnetw=g&hvrand=2381773061534257327&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9005825&hvtargid=pla-473522272714&psc=11. Drill small pilot holes for the self tapping screws index to thumb length all the way down the gutter.2. Repeat pilot holes through the magnetic strip.3. Zip tie the magnetic strip to the mesh, this side will face your home.4. Secure the mesh using the self tapping screws. This side is furthest away from your house, on the outside top of your gutter.5. Trim mesh (outside of gutter) to fit.The result for me is a permanently attached mesh with inside magnetic inside strip for ease of cleaning. The magnetic strip keeps the mesh from sagging and curling, which this stuff likes to do, it is a very cheap product and needs support.Depending on storm surge results, if too much pine gets built up in certain areas I will add another layer of mesh underneath the current on an as needed basis. The top mesh is large enough to break the water. The bottom mesh small enough to stop pine needles.This solution allows me to maintain the gutters by simply pulling up on the magnetic strip. This is specifically for the flat portions of my roof.For areas of the roof that are not flat, the magnetic strip may or may not be needed, just tuck the mesh underneath the shingles as shown in the video. I’m likely going to end up tacking the magnetic strip everywhere just because of how much easier it is to maintain the gutter. I want to avoid ever having to touch this mesh product again, it’s not easy to work with. Quite happy with how things are coming along! Storm surge updates to follow!

It is great stuff and I'm glad it's still available. I don't use it on the gutters but under the deck on the back of the house to keep birds from nesting. It is difficult to staple it in place, but it works great!

After this winter, I will know better if these hold down and don’t get blown out by the wind, but installation was fairly easy and they seem to be durable. Only time will tell.